思科路由器配置命令:思科交换机路由器配置命令大全 2024-05-03 07:21:26 0 0 交换机基本状态: switch:;ROM状态,路由器是rommon> hostname>;用户模式 hostname#;特权模式 hostname(config)#;全局配置模式 hostname(config-if)#;接口状态 交换机设置命令口令设置: switch>enable;进入特权模式 switch#configterminal;进入全局配置模式 switch(config)#hostname;设置交换机的主机名 switch(config)#enablesecretxxx;设置特权加密口令 switch(config)#enablepasswordxxa;设置特权非密口令 switch(config)#lineconsole0;进入控制台口 switch(config-line)#linevty04;进入虚拟终端 switch(config-line)#login;允许登录 switch(config-line)#passwordxx;设置登录口令xx switch#exit;返回命令 交换机设置命令VLAN设置: switch#vlandatabase;进入VLAN设置 switch(vlan)#vlan2;建VLAN2 switch(vlan)#novlan2;删vlan2 switch(config)#intf0/1;进入端口1 switch(config-if)#switchportaccessvlan2;当前端口加入vlan2 switch(config-if)#switchportmodetrunk;设置为干线 switch(config-if)#switchporttrunkallowedvlan1,2;设置允许的vlan switch(config-if)#switchporttrunkencapdot1q;设置vlan中继 switch(config)#vtpdomain;设置发vtp域名 switch(config)#vtppassword;设置发vtp密码 switch(config)#vtpmodeserver;设置发vtp模式 switch(config)#vtpmodeclient;设置发vtp模式 交换机设置命令设置IP地址: switch(config)#interfacevlan1;进入vlan1 switch(config-if)#ipaddress;设置IP地址 switch(config)#ipdefault-gateway;设置默认网关 switch#dirflash:;查看闪存 交换机设置命令显示命令: switch#write;保存配置信息 switch#showvtp;查看vtp配置信息 switch#showrun;查看当前配置信息 switch#showvlan;查看vlan配置信息 switch#showinterface;查看端口信息 switch#showintf0/0;查看指定端口信息 路由器显示命令: router#show run;显示配置信息 router#show interface;显示接口信息 router#show ip route ;显示路由信息 router#show cdp nei;显示邻居信息 router#reload;重新起动 路由器口令设置: router〉enable;进入特权模式 router#config terminal;进入全局配置模式 router(config)#hostname 〈hostname〉;设置交换机的主机名 router(config)#line console 0;进入控制台口 router(config-line)#line vty 0 4;进入虚拟终端 router(config-line)#login;要求口令验证 router(config-line)#password xx ;设置登录口令 xx router(config)#(Ctrl+z) ; 返回特权模式 router#exit ;返回命令 路由器配置: router(config)#int s0/0 ;进入 Serail 接口 router(config-if)#no shutdown ;激活当前接口 router(config-if)#clock rate 64000 ;设置同步时钟 router(config-if)#ip address 〈ip〉 〈netmask〉;设置 IP 地址 router(config-if)#int f0/0.1 ;进入子接口 router(config-subif.1)#ip address 〈ip〉〈netmask〉 ;设置子接口 IP router(config-subif.1)#encapsulation dot1q 〈n〉 ;绑定 vlan 中继协议 router(config)#config-register 0x2142 ;跳过配置文件 router(config)#config-register 0x2102 ;正常使用配置文件 router#reload ;重新引导 静态路由: ip route 〈ip-address〉 〈subnet-mask〉 〈gateway〉 ;命令格式 router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例 router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例 动态路由: router(config)#ip routing ;启动路由转发 router(config)#router rip ;启动 RIP 路由协议。 router(config-router)#network 〈netid〉 ;设置发布路由 router(config-router)#negihbor 〈ip〉 ;点对点帧中继用。 基本访问控制列表: router(config)#access-list 〈number〉 permit|deny 〈source ip〉 〈wild|any〉 router(config)#interface 〈interface〉 ;default:deny any router(config-if)#ip access-group 〈number〉 in|out ;default:out 例 1:router(config)#access-list 4 permit 10.8.1.1 router(config)#access-list 4 deny 10.8.1.0 0.0.0.255 router(config)#access-list 4 permit 10.8.0.0 0.0.255.255 router(config)#access-list 4 deny 10.0.0.0 0.255.255.255 router(config)#access-list 4 permit any router(config)#int f0/0 router(config-if)#ip access-group 4 in 删除访问控制例表: router(config)#no access-list 102 router(config-if)#no ip access-group 101 in 外部网关协议配置: routerA(config)#router bgp 100 routerA(config-router)#network 19.0.0.0 routerA(config-router)#neighbor 8.1.1.2 remote-as 200 配置 PPP 验证: RouterA(config)#username 〈RouterB〉 password 〈word〉 RouterA(config)#int s0 RouterA(config-if)#ppp authentication {chap|pap} 收藏(0)